Install TeamForge 17.8: All services on a single RHEL/CentOS 7.3 server

The easiest way to install TeamForge is to install it on a single server, dedicated to TeamForge taking the default configuration settings.

Before you begin:

Remember:

  • TeamForge 17.8 supports both RHEL/CentOS 6.9 and 7.3. See TeamForge installation requirements
  • For the ETL service to run as expected in a distributed TeamForge installation, all servers must have the same time zone.
  • While you can run both EventQ and TeamForge on the same server, CollabNet recommends such an approach only for testing purposes. It's always recommended to run EventQ on a separate server for optimal scalability. See EventQ installation requirements.
  • Installing or upgrading TeamForge needs root privileges. You must log on as root or use a root shell to install or upgrade TeamForge.

All the following services run on a single RHEL/CentOS 7.3 server (we call this server-01).

  1. Install Red Hat Enterprise Linux/CentOS 7.3 and log on as root.

    The host must be registered with the Red Hat Network if you are using Red Hat Enterprise Linux.

    See the Red Hat installation guide for help.

  2. Check your basic networking setup. See Set up Networking for more information.
  3. Configure your TeamForge installation repository.
    • TeamForge installation repository configuration for sites with internet access
    1. Contact the CollabNet Support and download the TeamForge 17.8 installation repository package to /tmp.
    2. Install the repository package.
      • yum install -y /tmp/collabnet-teamforge-repo-17.8-1.noarch.rpm
    3. Refresh your repository cache.
      • yum clean all
    • TeamForge installation repository configuration for sites without internet access
    1. Contact the CollabNet Support to get the auxiliary installer package for TeamForge 17.8 disconnected installation and save it in /tmp.
      • Red Hat Enterprise Linux/CentOS 7.3 64 bit RPM package: CTF-Disconnected-media-17.8.655-104.rhel7.x86_64.rpm
        Note: In addition to the above CentOS 7.3 64 bit RPM package, you must get the following CentOS 7.3 compatibility RPM, which is required for TeamForge 17.8 disconnected media installation on CentOS 7.3 profile: compat-ctf-dc-media-1.1-1.el7.noarch.rpm.
    2. Unpack the disconnected installation package.
      • rpm -ivh <package-name>
    3. Unpack the compat-ctf-dc-media-1.1-1.el7.noarch.rpm package if you are installing TeamForge 17.8 on CentOS 7.3.
      • rpm -ivh compat-ctf-dc-media-1.1-1.el7.noarch.rpm
    4. Note: If the Red Hat Enterprise Linux/CentOS installation DVD is mounted already, skip the following instructions. If not, mount the DVD.
      Mount the Red Hat Enterprise Linux/CentOS installation DVD. The DVD contains the necessary software and utilities required for installing TeamForge without internet access.

      In the following commands, replace "cdrom" with the identifier for your server's CD/DVD drive, if necessary.

      • cd /media/
      • mkdir cdrom
      • mount /dev/cdrom ./cdrom/

      If there are any spaces in the automount, unmount it first and mount it as a filepath, with no spaces.

    5. Create a yum configuration file that points to the Red Hat Enterprise Linux/CentOS installation DVD.
      • vi /etc/yum.repos.d/cdrom.repo
      Here's a sample yum configuration file.
      [RHEL-CDROM] 
      name=RHEL CDRom 			
      baseurl=file:///media/cdrom/Server/
      gpgfile=file:///media/cdrom/RPM-GPG-KEY-redhat-release 
      enabled=1
      gpgcheck=0
    6. Verify your yum configuration files.
      • yum list httpd
      • yum list apr
  4. Install the TeamForge application packages.
    • yum install teamforge

Important: The following warning message, which shows up during TeamForge install/upgrade (while installing CN-eventq rpm) can be safely ignored.
Don't run Bundler as root. Bundler can ask for sudo if it is needed, and
installing your bundle as root will break this application for all non-root
users on this machine.
...
...
Errno::ENOENT: No such file or directory - git
...
...

  1. Set up your site's master configuration file.
    • vi /opt/collabnet/teamforge/etc/site-options.conf
    1. Configure the services and domain name tokens.
      Note: cliserver and reviewboard-adapter are the new services added in TeamForge 17.4.
      localhost:SERVICES=ctfcore ctfcore-database mail etl ctfcore-datamart search subversion 
      cvs codesearch eventq mongodb redis rabbitmq cliserver
      localhost:PUBLIC_FQDN=my.app.domain.com
    2. Add Gerrit identifiers if you are installing Git.
      localhost:SERVICES=ctfcore ctfcore-database mail etl ctfcore-datamart search subversion 
      cvs codesearch eventq mongodb redis rabbitmq cliserver gerrit gerrit-database
    3. Add Binary identifiers if you are installing Nexus.
      localhost:SERVICES=ctfcore ctfcore-database mail etl ctfcore-datamart search subversion 
      cvs codesearch eventq mongodb redis rabbitmq cliserver gerrit gerrit-database binary binary-database
    4. Add Review Board identifiers if you are installing Review Board.
      localhost:SERVICES=ctfcore ctfcore-database mail etl ctfcore-datamart search subversion 
      cvs codesearch cliserver eventq mongodb redis rabbitmq  gerrit gerrit-database binary binary-database 
      reviewboard reviewboard-database reviewboard-adapter
    5. Attention: SSL is enabled by default and a self-signed certificate is auto-generated. Use the following tokens to adjust this behavior. To generate the SSL certificates, see Generate SSL certificates.
      Have the custom SSL certificate and private key for custom SSL certificate in place and provide their absolute paths in these tokens. SSL_CHAIN_FILE (intermediate certificate) is optional.
      SSL_CERT_FILE=
      SSL_KEY_FILE=
      SSL_CHAIN_FILE=
      Important: All SSL certificates including self-signed certificates are added automatically.
    6. TeamForge 7.1 and later support automatic password creation. See AUTO_DATA for more information.
    7. If the token REQUIRE_PASSWORD_SECURITY is enabled, then set this PASSWORD_CONTROL_EFFECTIVE_DATE token with a future date. If already set, reset the PASSWORD_CONTROL_EFFECTIVE_DATE with a future date while upgrading to TeamForge 17.8.
      CAUTION:
      The Password Control Kit (PCK) disables, deletes or expires user accounts that don't meet the password security requirements starting from the date set for the PASSWORD_CONTROL_EFFECTIVE_DATE token. If a date is not set, the PCK disables, deletes or expires user accounts immediately. You must set (or reset if required) this token with a future date. For example, you can use the following logic and pick a future date: PASSWORD_CONTROL_EFFECTIVE_DATE=<the day on which TeamForge upgrade is done> + PASSWORD_WARNING_PERIOD. See PASSWORD_CONTROL_EFFECTIVE_DATE for more information.
    8. If the token REQUIRE_RANDOM_ADMIN_PASSWORD is already set to true, then set the token ADMIN_EMAIL with a valid email address. ADMIN_EMAIL=root@{__APPLICATION_HOST__}
    9. If you have LDAP set up for external authentication, you must set the REQUIRE_USER_PASSWORD_CHANGE site options token to false.
    10. Make sure the PostgreSQL tokens in the site-options.conf file are set as recommended in the following topic: What are the right PostgreSQL settings for my site?
    11. Save the site-options.conf file.
  2. Provision services.
    • teamforge provision
    Note:

    TeamForge 17.4 (and later) installer expects the system locale to be LANG=en_US.UTF-8. TeamForge "provision" command fails otherwise.

  3. Restart TeamForge.
    • teamforge restart
  4. Verify TeamForge installation.
    1. Reboot the server and make sure all services come up automatically at startup.
    2. Log on to the TeamForge web application using the default Admin credentials.
      • Username: "admin"
      • Password: "admin"
    3. Create a sample project. See Create a TeamForge project
    4. Write a welcome message to your site's users. See Create a site-wide broadcast.